Top 10 Chest Lid Hinge – Cabinet & Furniture Hinges

As an Amazon Associate I earn from qualifying purchases.

1. SafeStay

#ad

SafeStay Lid Stay 105 Degree Open with Soft Close, Lid Support for Toy Box and Chest, Easy to Install

#ad
SafeStay #ad - Easy install instructions - easy to follow installation instructions ensure a perfect install the first time! Lid stay can be installed on either the left or the right side.

Gentle slow close design - Lids will lower slowly and gently to avoid crushing even the smallest of fingers. 100% money-back guarantee - if for whatever reason you are unhappy with the product we will refund you, no questions asked! Small compact design - the compact design allows for installation in tight fit areas. Holds lid open - never worry again about having to prop the lid open. This lid stay will hold the lid open until you are ready to close. The lid stay allows the lid to open at a maximum 105 degree angle.
BrandSafeStay #ad
ManufacturerSafeStay #ad
Height0.5 Inches
Length4.5 Inches
Width3.1 Inches

2. douper

#ad

Douper 200N Gas Struts Heavy Duty Soft Close Lid Support Hinges Automatic Slow Lowering Safety Pneumatic Lid Lifters Gas Springs Pack of 2

#ad
douper #ad - 75°-105° open angle -- each lid hinge can be used for right or left hand mounting, keep the hinge installed for 75°-105° adjustable opening angles, depending on actual situation. And must with a 9 inch clearance.

Hinges will not work if your lid doesn’t match specified dimension and weight requirement. Gently close design -- excellent safety solution for heavy hinged lids, lids will lower slowly and gently to avoid smashing fingers. Never worry again about having to prop the lid open. Strong enough -- douper 200n heavy duty gas struts can support maximum 30lbs lid and lower gently; Weight support will be doubled with 2 hinges 60lbs/ 2pcs.

Warm tips -- douper hinges will not applicable with the lid at width more than 50” and height over 25”. Holds lid open -- these hinges will hold your lid open until you push it down. Note: no adjustments on placement measurements of the hinge mounted on side board.
Branddouper #ad
ManufacturerDouper #ad
Height1 Inches
Length13 Inches
Width1 Inches
Part NumberDP057-TATAMI

3. douper

#ad

Douper Random Angle Lid Stays Tension Adjustable Lid Support Hinge Toy Box Hinge Maximum Weight Capacity 40lbs/2pcs 2 Pack

#ad
douper #ad - Douper lid support hinge for lifting the lid or flap of cabinet overhead kitchen cupboard caravan cabinet, treasure chest, duck house roof, and more window seat, storage chest project toy box, blanket box, work bench table desk, and book case. Random angle stays — keep your lid stay in place at whatever angle to need, it will not slam shut when the lid stays open and protect your fingers from smashing.

Items comes with detailed install instructions. Mark two points for drilling holes, and screw each mounting bracket into its respective place. The hinge is used for side-mounting and top-mounting. Durable material — douper lid stays are made of durable and sturdy zinc alloy in satin nickel, DO NOT remove the plastic clips or twist it hard once getting plastic clips fixed onto pin, never rust. Gift box packaging — a gorgeously exquisite gift choice for diy carpentry woodworking projects.

Adjustable tension — allow you to adjust 2pcs hinges weight capacity from 0lb to 40lbs by using Allen key to set up applicable friction pressure, such as ones of toy chamber, cabinet, cupboard and window seat, it is designed for supporting the lid weighing less than 40lb, and wardrobe, etc. Easy to install — our lid stay allows you to keep it installed for 75°, 90°, and 110° opening. Warm tips: since the plastic clip is a connecting piece, or they are breakable. Easy installation.
Branddouper #ad
Manufacturerdouper #ad
Height0.1 Inches
Length8 Inches
Width1 Inches
Part NumberFBA_DP056-Big
ModelFBA_DP056-Big

4. T Tulead

#ad

Tulead Spring Lid Support Left Right Lid Support Down Hinge Red Bronze Iron Support Box Cabinet Hardware Pack of 2 with Mounting Screws

#ad
T Tulead #ad - Spring lid support can be mounted on left or right positions. Max weight Support:30lbs. Total size:182x41x38mm/7. 2"x1. 6"x1. 5"l*w*h. Great for supporting lids on cabinet, chest, door, box, luggage, etc. Package content:2 x Spring Lid Support with Mounting Screws.
BrandT Tulead #ad
ManufacturerT Tulead #ad
Part NumberADD06180465

5. VOCOMO

#ad

Easy Install, VOCOMO Lid Stay 105 Degree Open with Soft Close, Lid Support Hinge for Toy Box

#ad
VOCOMO #ad - Small compact design - The compact design allows for installation in tight fit areas. Each hinge can be used for right or left side mounting. This lid stay will hold the lid open until you are ready to close. Lid support hinge - never worry again about having to prop the lid open. 105 degree open - the lid hinges supports opening the lid at a maximum Angle of 105 degree. Easy to install - easy to follow graphic installation instructions ensure a perfect install the first time. Soft close - lids will lower slowly and gently to avoid slams shut and crush the little fingers of children.
BrandVOCOMO #ad
ManufacturerVOCOMO #ad
Part NumberHinges-03

6. Selby Hardware

#ad

Lid Hinge Non Mortise Statuary Bronze

#ad
Selby Hardware #ad - Lid hinge non Mortise BRASS. For 3/4" material. Opens 190degrees. Non-mortise. Steel, brass plated.
BrandSelby Hardware #ad
ManufacturerSelby Hardware #ad
Part NumberH370PF34SB

7. VOCOMO

#ad

Safety Lid Support Soft Drop Lid Support Soft Close Lid Hinge for Cabinets Kitchen Chest 40lb/2pcs, VOCOMO Toy Box Hinges

#ad
VOCOMO #ad - It will not slam shut when the lid stays open. Adjustable tension - adjust tension with Allen wrench to fit for lids with different weight. You can also refer to the installation instructions in the fifth picture.

360 degree random stay - adjust the lid opening angle, and keep it stay in place at different angles without time limit. After installing the hinge, please tighten the mechanism into Allen wrench hole to prevent lid from slamming shut. The weight of the lid cannot exceed 40lbs. Gentle slow close design - lids will lower slowly and gently to avoid crushing even the smallest of fingers. Easy install instruction - easy to follow installation instructions ensure a perfect install the first time! We provide installation instructions for 70°, 90° and 100° opening. No risk purchase - We provide worry-free lifetime warrantyno man-madeand friendly customer service.
BrandVOCOMO #ad
ManufacturerVOCOMO #ad
Part NumberCH00131

8. National Hardware

#ad

National Hardware N147-181 V550 Chest Hinges in Brass, 2 pack

#ad
National Hardware #ad - 2 pack. Hinges and screws are semi-concealed when hinge is closed. Tight pin for more secure applications. Manufactured with hot-rolled steel. Designed for chests, storages boxes, cabinets, etc.
BrandNational Hardware #ad
ManufacturerNATIONAL HARDWARE #ad
Height3.1 Inches
Length7 Inches
Width6.1 Inches
Part NumberN147-181
ModelN147-181

9. SEN

#ad

Gas Shocks, Gas Spring, Soft Close Hinges, Gas Strut, Lid Support, Pressure 120N, Kitchen Cabinet Hinges Hydraulic Support Door Cabinet Hinge Spring, Toy Box Hinges, Lift Supports

#ad
SEN #ad - Since the gas struts need to be installed by themselves, choose the model and quantity according to the weight of the actual cabinet door panel. Avoid the loss of gas in the cavity 3. The connection point should be installed flexibly without jamming. 120n gas shocks suit best for the door weight 100N-120N,The door panel weighs more than 26lb, so use two or higher pressure models.

The choice is not soft and hard, and two for cabinet door width >600mm/23. 6in to achieve parallel opening and closing synchronization. You should consider whether you can install them independently. If you need to adjust the direction of the joint, not upside-down, you can only turn it to the right. Pressure:120n/26lb/12kg per strut;length hole center to hole center :9-11/16'';travel:3-14/25'', 12kg, it is not suitable for use.

2. The gas spring piston rod is strictly prohibited from rotating to the left. Stable & no rusty: gas struts is made of copper core with zinc plating, which prevents from rusting even aftering using for a few years. If there is a problem with the product or installation difficulties, please contact customer service as soon as possible to send installation pictures or videos, thank you. Install the nail plate and insert the ball into the plastic hole.
BrandSEN #ad
ManufacturerSEN #ad
Part NumberSEN

10. RUYUFE

#ad

Heavy Duty Lid Support Hinges Soft Close Folding Lid Stay Hinge, Kitchen, Perfect for Cabinet, Wardrobe Toy Chamber Max Support 50lb/2pcs, Keep Lid Hinge Open

#ad
RUYUFE #ad - Durable material -- the up-grated version has the advantages of strong bearing capacity, Metal connector instead of plastic clip. Weight capacity 50lb—lid stay max weight support 50lbs/2pcs, lid support hinge can be mounted on the left or right side.

90°, upward door open adjustable angle of 75°, 110° by yourself. Perfect for any lids or flaps when a soft closing motion is required. Lid support hinge usage—the lid support hinge support the lids of box, cabinet, closet, such as toy box, wardrobe lids. Never worry about having to support lid hinge anymore. Easy to install – only following the placement measurements on the instructions, you can easy to install lid stay.

Keep the lid open- the lid hinge will hold the lid open until you want to close. Made of premium quality zinc alloy with maximum corrosion resistance and durability the lid stay hinges guarantee high performance. Allen wrench and exclusive redesign Installation instruction in package. Heavy toy chest lid to prevent fingers from getting smashed.
BrandRUYUFE #ad
ManufacturerRUYUFE #ad