Top 10 Solder Wick Braid with Flux – Welding Equipment & Accessories

As an Amazon Associate I earn from qualifying purchases.

1. NTE Electronics


NTE Electronics SW02-10 No-Clean Solder Wick, 10' Length, 4 Blue.098" Width

NTE Electronics #ad - 100% copper wick has fine braid design to promote strong capillary action to pull in excess solder. Residue left behind is halide free and non-conductive, so it does not have to be cleaned off the board. Removes up to four times more solder than conventional wick, and extracts solder much faster than wicks based on Type-R fluxes. Available with standard or anti-static bobbins.
BrandNTE Electronics #ad
ManufacturerNTE Electronics, Inc. #ad
Part NumberSW02-10

2. Ferraycle


No Clean Soldering Flux Pen and Solder Remover Wick, 0.1 Inch Wide and 59 Inch Long, Solder Braid Wick Liquid Solder Flux Pen for Electronics Welding Repair Tabbing Wire Maintenance 6 Pieces

Ferraycle #ad - Suitable size: the rosin flux pen measures about 14. 3 cm/ 5. 6 inches in length, and the solder braided wick is about 1. 5 m/ 59 inches long and 2. 5 mm/ 01 inches wide, which is convenient to hold in hand; Please check the size carefully before purchasing. Package includes: you will receive 3 pieces of no clean solder flux pens, and 3 pieces of soldering braided wick, in total of 6 pieces, sufficient quantity and a considerate combination to meet your needs for daily use and replacement.

Quality material: these no-clean soldering wicks are made of quality copper wire and adopt precise weaving technology, which can enhance tension on the surface to absorb excess solder; The liquid solder pen is made of reliable materials, no leaking and safe for protecting the flux, preventing you from touching the organic solvents. Wide applications: these flux pens and braided solder wicks can be applied for laboratory, electronics welding, etc.

Computer, home repairs and correcting small PCB board errors and through-hole solder joints, bringing a lot of convenience to your work and improving efficiency. Practical tools: 10-ml solder flux pen with soft brush tip can release the liquid flow moderately, which can clean the components without harming the PCB board copper foil or IC pin; The solder remover wick features good thermal conductivity and absorption, useful to reduce the risk of thermal injury to the circuit boards.
BrandFerraycle #ad
ManufacturerFerraycle #ad
Part NumberFerraycle-Flux Pen-17



Desoldering Vacuum Pump Solder Removal Tool, AUSTOR Desoldering Sucker and 6 Pcs Solder Braid Wick 2.0mm/2.5mm/3.0mm Width, 1.5m Length with Flux

AUSTOR #ad - Desoldering braid wick with rosin - 6 pieces copper solder braid in 3 size, width 2. 0mm/2. 5mm/3. 0mm, 2 pieces for each size; geometrically-precise weave, can be used to clean the spare solder on the pin away to avoid short circuit, length 1.

5m, to meet your various of soldering needs. Wide application - correcting mistakes on small PCB boards, cleaning small components, removing relays and other components from printed circuit boards, re-soldering and desoldering. High quality material - the desoldering pump body made of premium quality ABS material, with non-slip sponge and nylon nozzle, anti-static, heat resistant and durable.

High efficiency solder sucker - the desoldering pump designed with double ring and "vacuum" open button, you can remove solder from circuit board effectively by cocking it and pressing the trigger button with one hand. 7-in-1 solder removal tool - 1pcs solder sucker and 6pcs solder wicks in 3 size.
BrandAUSTOR #ad
ManufacturerAUSTOR #ad
Height0.79 Inches
Length7.48 Inches
Width5.12 Inches



Desoldering Wick Used to Remove the Solder and Disassemble Electrical Components, TOWOT Solder Wick, No-Clean Solder Wick BraidW 0.12'' L 9.8'

TOWOT #ad - Extensive applications: the braided solder wicks are suitable for labs, school, home, and industrial welding work; And the wicks adopt a fine braid design to promote strong capillary action, bringing more convenience to your daily work.

Easy to use: the desoldering wicks can provide an easier way to correct mistakes on small PCB boards and will not make damage to the board, clean small components, suitable for re-soldering and desoldering. Low residue design: no-clean solder wick braid will just leave little residues after use and the residues are non-conductive and non-corrosive, no need to waste your time cleaning it.

Quality materials:the braided desoldering wicks are made of 100% copper wires with a fine braid design. Warranty :if you have any questions, please feel free to contact us at any time. Using flat stitch weaving, fast heat conduction, to promote strong capillary action to pull in excess solder. Thank you! .
BrandTOWOT #ad
ManufacturerTOWOT #ad
Part NumberTOWOT
ModelW 0.12'' L 9.8'

5. MG Chemicals


0.075" Width x 5' Length, MG Chemicals 425-NS No Clean Super Wick Desoldering Braid

MG Chemicals #ad - Conforms to mil-f-14256e rma flux and J-STD-004. Environmentally and PCB safe residues. Nsf, nonfood compounds program Listed P1, NSF Registration #144209. Esd electrostatic dissipative safe for 1. 5 m 5 ft bobbins. High purity, oxide-free copper.
BrandMG Chemicals #ad
ManufacturerMG Chemicals #ad
Height0.39 Inches
Length1.57 Inches
Weight0.02 Pounds
Width1.57 Inches
Part Number425-NS
Warranty[email protected]

6. MG Chemicals


Blue, 50' Length x 0.1" Width, MG Chemicals 454 Desoldering Braid #4 Fine Braid Super Wick with RMA Flux

MG Chemicals #ad - Designed to leave a residue that is environmentally safe. Oxide-free clean copper. Only pure type 'rma' rosin is used meeting the requirements of MIL-F-14256F ANSI/J-STD-0004. Manufactured under SPC guidelines. Static free bobbins.
BrandMG Chemicals #ad
ManufacturerMG Chemicals #ad
Height0 Inches
Length0 Inches
Weight0.11 Pounds
Width0 Inches
Part Number454

7. Hotop


1.5 meter Length Lake Blue,0.04 Inch Width, 6 Pieces Solder Wicks No-Clean Solder Braided Wicks Desoldering Wicks

Hotop #ad - Easy to use: the desoldering wicks can provide a easier way to correct mistakes on small PCB boards and will not make damage to the board, clean small components, suitable for re-soldering and desoldering.

What you get: come with 6 pieces of no-clean solder wicks, each wick is about 1 mm/ 004 inch in width and 1. 5 m/ 5 feet long, enough quantity and length for your daily needs. No-clean design: the solder braided wicks will just leave little residues after use and the residues are non-conductive and non-corrosive, you do not need to spending time removing them from the boards. Reliable material: the desoldering wicks are made of copper wires with nice quality, precise weaving design can improve the capillary effect and the redundant solder absorbing ability, increasing your efficiency.

Wide applications: the braided solder wicks are suitable for labs, practical tools to remove solder and correct errors on small PCB boards, home and industry welding work, bringing lots of convenience for your work.
BrandHotop #ad
ManufacturerHotop #ad
Part NumberHotop-No-Clean Solder-0818

8. Auto Supply Mall


10-50L 0.10", 50ft., Rosin, Chemtronics Desoldering Braid, Chem-Wik

Auto Supply Mall #ad - Ultra-thin desoldering wick. Better thermal conductivity, even at low temperatures. Overheating minimized by requiring less heat for shorter time. Lighter mass and pure copper braid construction. Responds as much as 50% faster than conventional desoldering braids.
BrandAuto Supply Mall #ad
ManufacturerCHEMTRONICS #ad
Weight0.15 Pounds
Part Number10-50L

9. Herain


Desoldering Wicks Removal Tool Solder Sucker Used to Remove the Solder and Disassemble Electrical Components9.84 ft Length 1, Herain No-Clean Solder Wick, Desoldering Braided Wicks with Flux

Herain #ad - 1. High-quality materials: the desoldering wick is geometrically precisely braided with high-quality copper wire, which is resistant to oxidation and corrosion, low residual and no halide, has good thermal conductivity, and clean tin absorption.3. Widely used: no-clean desoldering wick is suitable for welding work in laboratories, schools and homes, industries, electrical appliances, It is suitable for all kinds of electronics, precision instruments and meters.

5. Ingenuity quality: 1 piece of no-clean solder braided wick 0078 inch wide, which is sufficient to meet your work requirements. If you have any product questions, 9. 84 ft length, you can contact us at any time. 2. Geometric braid design: the solder wick adopts a precise geometric braid design, which ensures a large surface tension and tin absorption ability, and reduces the risk of thermal damage to the circuit board.

The main board desoldering spot is removed, and it is used with the soldering station. It can absorb tin quickly and a large amount of tin, and is dedicated to remove excess solder. 4. Easy to use: the desoldering braid wick is used to absorb excess solder when removing tin, the fine woven design promotes strong capillary action to suck in excess solder.
BrandHerain #ad
ManufacturerHerain #ad
Height0.4 Inches
Length1.85 Inches
Width1.85 Inches
Part Numberxxx-01

10. Tabiger


Solder Sucker & Desoldering Wick, 1.5m Length- Desoldering Vacuum Pump Solder Remover, Tabiger Solder Wick & Desoldering Pump, 2pcs Solder Braid 2.5mm Width

Tabiger #ad - Abs body with non-slip sponge and nylon nozzle desoldering pump the body of the desoldering vacuum pump is made of high quality ABS, the nylon nozzle of the solder suck can endure high temperature, make it comfortable to hold, which make the solder sucker delicate and durable, also the covered sponge can absorb sweat and heat, thus it can be used for a long time.

One-handed solder sucker with powerful suction whether you are right or left-handed, the desoldering pump designed with double ring double open and "vacuum" button, you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready, which make the sucking power awesome. Desoldering wick with copper braid 2pcs solder braid with the size 2. 5mm width, this desoldering wick has geometrically-precise weave with copper and rosin, 1. 5m length, once the desoldering wick and the solder has been heated, work from the tip of the desoldering wick, the solder braid can quickly absorbed molten solder and left a clean working area.

Widely used solder remover the desoldering wick & desoldering pump can be used to correct mistakes with small boards on PCBs, desoldering computer parts such as a motherboard, re-solder mechanical keyboard switches, unsoldering old wire from devices, remove relays and other components from printed circuit boards, clean alloy on smd components and more.3-in-1 solder removal tool 1pcs desoldering vacuum pumps and 2pcs solder wicks, a must-have tool for electronics kit, while the solder wick is better for small amounts of solder, the desoldering wick absorbs solder, the desoldering pump pulls it away quick, the solder sucker takes up large amounts.
BrandTabiger #ad
ManufacturerTABIGER #ad
Height0.7 Inches
Length9 Inches
Weight0.17 Pounds
Width4 Inches
Part NumberTB-02-US